Zip-line construct with no trees
Disclaimer: Use your own judgement or consult an expert before installing your own zip line. This site describes my idea procedure, strategies, and execution. Install and use at your own risk.
So I wanted to build a zip line in my backyard butttttt my backyard doesn’t have any trees, I looked around and couldn’t locate directions for setting up a zip line with posts so I decided to write about it for all you newbs out there. There are several challenges with using posts.
Fist I grabbed a DIY Zip Line Cable Kit from Ziplinestop.com
First is the height difference. Predicated on the directions that came with the kit, for the 60 foot jog, the zip line desires around 30 inches of height difference. The beginning height ought to be about 102 inches as well as the finishing height would be about 72 inches.
I utilized a laser level (SKIL MT 8201-Self-Leveling Cross Line Laser) as well as a yard stick to gauge the difference in altitude between the beginning and ending of the zip line run in my backyard. Fortunately, I ‘d around 22 inches of altitude change. What this means is that I just need 8 added inches of height differential for my setup.
Second is the tension in the cord. The kit uses 1/4″ steel cable with a tension of 300 pounds with no load and 600 pounds maximum tension. It will be extremely tough to place posts in the ground which could resist that quantity of force without bending over and losing pressure.
I thought of two alternatives to the stress issue.
1. Brace the posts with struts or wire anchored to the ground.
2. Anchor the cord anchor to the in the ground on both ends and go over the posts with pulleys.
I selected option 2 since it looked simpler to execute.
It’s obvious that a lot of the tension is tolerated by the concrete anchors in theground because the posts are subjected to a bending force that is dependent upon the angle of the cable as it turns across the pulley. The farther away from the post the anchor is set, the less bending force (and total force) on the place.
This layout can be further enhanced by angling the posts away from each other by 5 or 10 degrees.
Here is the starting pressure treated lumber post for the zip-line. I used two ground anchors which join together and attach to the wire. The first anchor position was not in line with the zip-line and it caused too much lateral force on the pulley resulting in a broken pulley. I used the second ground anchor to properly align the system. The horizontal section of chain 2/3rds up was used to increase line tension and balance bending forces on the post. Note that the post is angled backwards about 10 degrees from vertical. This also reduces bending forces.
I used a 4×6″ pressure treated wood post 12′ length. The hole was dug approx 4-1/2′ deep, 2′ across and 2′ wide. A small amount of crushed stone was placed at the base and impacted. Then the post was set. It was angled away from the opposite post 5-10 degrees. Then the crushed stone was placed and impacted around the post using a 2×4 and bricks. The stone was finally covered with dirt and grass.
I dug a hole about 2 feet deep, 3 feet across, and 2 feet long. I tried to make sure the base of the hole was wider than the top of the hole. Two rebar rods were impacted in the base of the hole angling away from the chain direction as shown. A third rebar rod was threaded through the last link on the heavy chain and placed behind the upright rebar rods. This arrangement is able to hold tension without any cement. Next, two 80 pound bags of concrete mix are prepared and poured into the hole. Dirt is packed on top of the anchor once the concrete sets.
Zip Line Kit From Zip Line Stop. This one is made for kids but can hold up to 225 pounds. It comes with the trolley, cable, and most of the hardware that I needed. Cost $229
Alien Flier R100 kit
4×6″ x 12′ Pressure Treated Timber. Cost about $25.00 each from Home Depot.
Koch 3202093 2 Cable Block Fixed Flange, Zinc Plated Pulleys from Amazon. I bought 2 at first but needed an additional one to handle the high force on the starting side. Cost $6.99 each as of 7/18/2013.
Koch A01211 1/4 by 20-Feet Grade 30 Proof Coil Chain , Zinc Plated
Seymour Promotional Post Hole Digger with Wood Handle DG-60
1 Cubic Yard of 3/4″ crushed stone from local stone yard. $30 delivered.
1/2″ Rebar for the cement anchor, I cut it up into 2-3 foot sections and used 2 pieces per anchor for a total of about 12′. Cost about $15-$20 total depending on where you buy it. I had some pieces lying around from a previous project.
Steelworks Boltmaster #4-1/2X72 Rebar 11804 Rebar W/Smooth Rods
Since the cable can break at the loop, I reinforced the loops with thimbles for added security. The kit had one so I bought one for the other end of the cable.Koch 143121 Wire Rope Clips and Thimble for 1/8-Inch Cable, Zinc Plated. Cost $4 on Amazon as of 7/18/2013.